NEW FUCKING EAZY FREEBASE PSEUDO EXTRACTION!!!

[NeverSleepy]

Crush ANY pills that only contain pseudoephedrine as the active ingredient

Boil pill powder in 40% lye water without letting any steam evaporate or you will lose pseudo

Continue boiling until color goes from yellow to black [few hours]

Add np, shake then pull off

Repeat np pull

Add the two np pulls together

Wash np with h2o twice

Dry np with calcium chloride [damp-rid]

Evaporate np until only pseudo oil remains

Freeze the oil, scrape then do what you want with it before it melts



FUCK THE STB and E_GULL and W_A/B and TURPS_CURE and STEAM_DISTILLING

THIS GIVES +95% yeilds of 100% pure escential oil in just a few hours useing cheap, easy to get chems [lye/h2o/damp-rid/kingsford]

[gottagogo]

[QUOTE]Originally posted by NeverSleepy:

[B]Crush ANY pills that only contain pseudoephedrine as the active ingredient

Boil pill powder in 40% lye water without letting any steam evaporate or you will lose pseudo

So you're going to boil water for a couple of hours without letting any steam escape. I doubt it. Luckily, pseudo is not as volitile as meth and perhaps SWIM is a little off base on this one. Also, maybe you are forgetting about the drymatrix formulations that have an additive used specifically to run up into the non polar layer (and mess up your rxn.) if it is not removed first. Maybe you should use the bleach test to determine the purity of your pseudo. As for newbees and inexperienced individuals, if tetra is available to you, it is by far the easiest and SWIM believes its the best all around cure available.



FUCK THE STB and E_GULL and W_A/B and TURPS_CURE and STEAM_DISTILLING

THIS GIVES +95% yeilds of 100% pure escential oil in just a few hours useing cheap, easy to get chems [lye/h2o/damp-rid/kingsford]

SWIM in no way believes that you can achieve this kind of yield from this kind of extraction. If there are any chemists out there please tell SWIM what they think.

[NeverSleepy]

Go spend a few bucks and give it a try pussy.

The "base boil" releases the pseudo from whatever chem is holding it the water so it can be extracted via np. I just vaporized some of this oil on foil and it didnt even leave a trace of anything behind.

[tryptamine]

so when you add the lye water to a pill powder that has carboxomethylcellulose and the mass turns into gell and you boil this and it burns does it still work.

[NeverSleepy]

Yes

[t3knology]

sorry for the n00b question, but what is NP?

[DrY.R.Head]

NP solvent means a non-polar solvent. For example; benzine(Colmen fuel), toluene, petroleum distillates (white gasalines)

and ethers.

NP's can be used to pull oils out of solutions. As decribed above.

[tryptamine]

Colemans fuel is not benzene, it is petroleum ether. It has crappy rust inhibitors in it so you should distill it before use.

[frankz81]

how do u use the tolulene to 'pull' out the oil?? do u drain in or freexe n scrap it?

thanks

i am very new to this and need all the help i can get,i am still experimenting as i am sure most of u were in my position unless being shown,if anyone wants to email me with the most simplest way (i didnt do chemistry) id appreciate that soo much!

[junglizt]

JUST A QUESTION?? I HAVE LOOKED FOR TOLUENE ALMOST EVERYWHERE. ALL I CAN FIND IS XYLENE. IT IS USED IN PLACE OF TOLUENE CUASE OF IT'S SLOW EVAP RATE. IS IT ADVISABLE TO USE THIS???

[gottagogo]

jung, dude lay off the caps, please. The answer is almost universally yes. Xylene can be substituted for toluene in every case involving OTC pill extractions I have ever read. That doesn't mean it is without exception, but it is doubtful you will run into any problems with xylene.

The guy with the broad "how to make meth" question. Try to figure out one thing at a time. Start with something really easy to do- - say pulling good, clean red phosphorous from a shitload of matchbooks - - like maybe the store brand from the drugstore that sound like painting your wall with a mixture of blue and yellow. Look for info on the use of acetone and Hcl. to fascilitate this operation, then step up to the next course. Do not take information or procedures lightly or as automatically accurate just because it appears in print. If someone posts about the "super fast, super easy" method for anything and you cannot find substantial confirmation from known names (or those with a lot of posts to their credit) then its probably not all its cracked up to be and should definitely be avoided by beginners desiring confidence building success, no matter how small.

As for neversleepy, you really disappoint me. I didn't make the connection the other day when I read your little taunt, but its all the more reason to check your mail. Trip. took it easy on you. But you, me, and everyone else who knows anything can tell the difference between a talker and a doer.

For those who know very, very little, avoid this guys advice. Maybe he's right, maybe he's not, but for sure there are more reliable sources out there.

Use your brain. It's not too busy.

[NeverSleepy]

Yea, guess I forgot to tell you totse fools that this was just some made up bullshit.

[darkchild]

toluene is available at most print shops. they use it as a print roller cleaner and usually have a couple of 55 gallon drums around.

[crashnburn]

good advice gottagogo for us new bees much appreciated...not that im that stupid to jump and do anything i read the first time without doing some research first tweek on brother.....